Wheelchair and Scooter Carriers
Results: 96
Abiloader-Fx
The AbiLoader-FX is a wheelchair loader for car, pickup truck, sport utility vehicle and van designed for use by people with lower extremity or mobility disabilities, spinal cord injury and other who use wheelchairs. It is intended for use with wheelchairs with fixed frames that do not fold. The device is installed in the trunk or rear storage area of a vehicle into which the folded wheelchair will fit. The AbiLoader-FX has a robotic arm with two actuators and a mechanism to grab and hold a whee
Ameriglide Auto Scooter Lift 350
The AmeriGlide Auto Scooter Lift 350 is a hitch-mounted scooter carrier designed for use by individuals with mobility disabilities. The self-adjusting hold down arm is compatible with most scooters on the market. As the large aluminum platform starts to lift after the user drives the scooter onto it, the hold down arm engages automatically and applies the right amount of tension to hold the scooter securely in place. The platform also folds up automatically when not in use. The lift can carry sc
Ameriglide Extender Plus
The AmeriGlide Extender Plus is a scooter or wheelchair loader for van designed for use by individuals with mobility disabilities. This interior-mounted lift can load a power chair or scooter into a full size van or minivan for transport. The lift is constructed from steel with a protective finish. It has an industrial rated 12-volt motor. The user drives on and connects the strap, and the lift loads the scooter or wheelchair. The maximum travel distance from the ground 26 inches. POWER: Uses ba
Ameriglide In-N-Out Mini Universal Lift 200
The Ameriglide In-N-Out Mini Universal Lift 200 is a hitch mounted or in-the-vehicle carrier for smaller power chairs or scooters. With this lift, the user can store a power chair or scooter inside a vehicle for transportation. This weather-resistant lift also installs on Class II or Class III hitches. OPTIONS: Wireless remote; docking device for Shoprider, Pride, or other scooter brands; receiver hitch. CAPACITY: 200 pounds. WEIGHT: 35 pounds. WARRANTY: Transferable limited 3 year warranty.
Ameriglide Manual Wheelchair Lift 100
The Ameriglide Manual Wheelchair Lift 100 is a hitch-mounted wheelchair lift designed for use by individuals with mobility disabilities or spinal cord injury. The user places a folded manual wheelchair onto the platform, then pushes a button to raise the wheelchair. The lift can be installed on almost any vehicle with a class I, II, or III hitch as well as standard ball mounts. OPTIONS: Swing-away arm; manual wheelchair cover; receiver hitch. POWER: Uses vehicle battery. DIMENSIONS (HxW): 5 to 1
Ameriglide Mini Power Chair Lift 135
The Ameriglide Mini Power Chair Lift 135 is a hitch mounted wheelchair loader designed for use by individuals with mobiity disabilities or spinal cord injury. It can be mounted onto a Class I, II or III trailer hitch from 5 to 19 inches high and used to transport most portable electric wheelchairs. A strap system secures the wheelchair to the lift. The lift is battery powered with a manual folding platform. Using the manual backup crank, the lift can be operated if the battery looses its charge.
Ameriglide Mini Scooter Lift 135
The Mini Scooter Lift 135 is a hitch mounted scooter loader designed for use by individuals with lower extremity, mobility, or walking disabilities. This powered lift can attach to a Class I, II, or III hitch from 5 to 19 inches high, and supports most 3- and 4-wheel micro-scooters. It has a manual fold down platform and a manual override, so it can be operated in the event of a power disruption. The scooter is held in place with a strap. POWER: Uses battery. An optional battery pack is availabl
Ameriglide Mini Universal Lift 200
The Mini Universal Lift 200 is a trunk mounted scooter or wheelchair loader designed for use by individuals with mobility disabilities. This inside lift can be used for transporting micro or travel size power chairs or scooters. It can be installed in the vehicle's trunk or cargo area. It rotates manually and can be disassembled for storage when not in use. POWER: An optional battery pack is available. OPTIONS: Wireless remote and docking device (Shoprider, Pride, or others). DIMENSIONS: 37 inc
Ameriglide Rear-Door Drive-Thru Lift 350
The Rear Door Drive-Thru Lift 350 is a powered wheelchair or scooter loader for vans designed for use by individuals with mobility disabilities. This lift attaches to the vehicle's third-row seating hardware. When in operation, a platform extends out on rails from inside until it clears the rear of the vehicle. From there, the platform lowers to the ground. The user drives the power chair or scooter onto the platform, attaches the straps, and presses a button on a remote hand control. The power
Ameriglide Side Door Drive-Thru Lift 275
The Side Door Drive-Thru Lift 275 is a wheelchair or scooter platform lift designed for use by individuals with mobility disabilities. The lift installs on second row seating harware, so the power chair or scooter can be delivered near the passenger or driver's door making it more convenient to move from mobility device to vehicle and back. When the lift is in operation, a platform extends out on rails from inside the vehicle until it clears the side. From there, the platform lowers to the groun
Ameriglide Tilt-N-Go 350 Mini Lift
The Ameriglide Tilt-N-Go 350 Mini Lift is a hitch-mounted scooter carrier designed for transporting travel-size scooters. This all- aluminum carrier uses a 2-inch Class 3 hitch. OPTIONS: Class 2 hitch adapter; mobility cover; Class 3 Receiver Hitch. DIMENSIONS (LxW): Usable platform area is 44 x 24 inches. CAPACITY: 350 pounds. WEIGHT: 46 pounds.
Ameriglide Universal 250 Lift
The AmeriGlide Universal 250 is a automobile or sport utility vehicle (SUV) lift for smaller electric wheelchairs and scooters. It is an internal vehicle lift that allows the scooter or power chair to be stored inside the user's automobile. The lift has an integrated offset post to help clear the vehicle's bumper, and its base is adjustable to better match the vehicle's dimensions. Its telescoping boom rotates manually, with adjustable length and pitch to allow the user to attach the lifting str
Ameriglide Universal 350 Truck Bed Lift
The Ameriglide Universal 350 Tuck Bed Lift is a scooter or wheelchair loader for pickup trucks designed for use by individuals with mobility disabilities. With the push of a button, this unit can lift almost any mobility scooter or electric power wheelchair into a truck's bed using a boom arm and powered rotation (PR). It can be mounted on either side of the vehicle in most pickup trucks, whether it has an extended bed or an extended cab. Made from weather- resistant materials, the unit has an a
Ameriglide Universal 400 Pr Chair And Scooter Lift
The Ameriglide Universal 400 PR (Power Rotation) Chair and Scooter Lift is a wheelchair and scooter loader designed for use by individuals with mobility disabilities. This lift has a powered rotation boom for loading. It mounts inside the vehicle on either side and has an adjustable base and boom. An integrated offset post ensures that the user's scooter or wheelchair clears the vehicle's bumper. The telescoping boom has adjustable length and pitch that adjusts from 0 to 30 degrees. The unit has
Ameriglide Universal Outside Lift 350
The Universal Outside Lift 350 is a hitch mounted wheelchair or scooter loader designed for use by individuals with mobility disabilities. This lift works with both Class II and Class III hitches, and with most mobility scooters and electric power chairs. The user drives the scooter or wheelchair onto the aluminum platform and secures it in place using the built in retractors. Once the retractors are locked in place, the user pushes a button. The lift. DIMENSIONS: This loader can hold scooters u
Ameriglide Universal Outside Lift 350 Xl
The Ameriglide Universal Outside Lift 350 XL is a wheelchair or scooter loader designed for use by individuals with mobility disabilities. This unit can lift larger electric wheelchairs and scooters with wheelbases up to 48 inches long. Retractors lock the wheelchair or scooter in place. Due to its size, this unit works only with a Class III hitch. The unit comes with a standard Class III hitch receiver. POWER: Uses battery. An optional battery pack is available. OPTIONS: Swing-away arm; scooter
Amigo Lift-It
The Amigo Lift-It is an electric, hitch-mounted wheelchair/scooter loader with a built-in control designed for use by individuals with mobility disabilities. The lift is designed to be installed on cars, vans, or trucks with Class II or III receiver hitches and swing-away or hatch-type doors (fold-down tailgates not compatible). No permanent installation is required, and the lift is fully transferable between vehicles. The Lift-It disassembles into four lightweight components when not in use so
Armstrong Lift
The Armstrong Lift is a powered or manual wheelchair or scooter loader for sport utility vehicles (SUVs)designed for use by individuals with mobility disabilities or spinal cord injury. With the lift in its folded position, the ultra-compact, left-mounted single post design creates 100 percent clear interior floor space, a clearer side view, and allows the rear passenger seats to be fully assembled for use. The side-mount design increases rear bumper clearance for loading and unloading and the a
Atlas Electric Scooter Lift
The Atlas Electric Scooter Lift is a scooter or wheelchair loader for automobile trunks, vans, pickup trucks, and sports utility vehicles. This lift works with either three or four-wheeled scooters and manual or power wheelchairs weighing up to 250 pounds. This loader features a patented Lift'n Latch Boom Arm. The user lifts the arm up and a spring-loaded latch locks the arm in the raised position. Lifting the arm again releases the latch automatically, allowing the arm to be lowered. The contro
Atlas Hitch Lift
The Atlas Hitch Lift is a hitch-mounted scooter loader designed for use in vans or sport utility vehicles with third row seating that is not easily removed or does not fold into the floor. The lift works with three- or four-wheel scooters and manual or powered wheelchairs weighing up to 250 pounds. The rear hitch base assembly mounts to a Class II or III hitch. The swing arm enables the rear hatch door to be used without removing the base assembly. This loader features a patented Lift'n Latch Bo
Automatic Power Chair Lift (Model Al550)
The Automatic Power Chair Lift, model AL550, is a platform van lift designed for use by individuals with mobility disabilities or spinal cord injury. The lift's docking station features a self-aligning base, enabling the user to drive onto the platform and be locked in place. An audible latching sound is heard as the chair's pin passes into the locking mechanism, and attempting to back the chair verifies that the latch is locked. The docking base also includes a bright colored indicator pin to c
Back-Saver Vehicle Lift (Model Awl-1600)
The Back-Saver Vehicle Lift, model AWL-1600, is a bumper-mounted wheelchair carrier designed to transport a folding wheelchair on an automobile with limited trunk or interior space. The automatic, motorized lift secures the folded wheelchair against the rear bumper, latching on the arms and supporting the rear wheels (22 inches in diameter or larger) in brackets. The lift includes an emergency safety latch and a state and federally approved license plate holder. CAPACITY: Carries wheelchairs wei
Bruno Big Lifter (Model Vsl-570)
The Bruno Big Lifter, model VSL 570, is a wheelchair and scooter loader designed for use at the rear of minivans, sport utility vehicles, and full size vans. The Big Lifter's manual swing has a low-resistance design, requiring minimum strength. Installation requires no structural modification. The adjustable low-profile arm allows the placement of larger power bases into smaller vehicle openings. A Bruno Custom Base provides for mounting the lift in the appropriate location. POWER: Big Lifter is
Bruno Offset Space-Saver (Model Asl-350)
The Offset Space-Saver, model ASL-350, is a trunk-mounted scooter loader designed to load a partially assembled three-wheel scooter in the trunk of a car. The offset design of the lift arm allows the user to position the scooter inside narrow trunk openings. All controls are located on top of the lift arm. The unit disassembles with three steps and can be stored in the vehicle or in the trunk. When an additional tower base assembly is ordered, the loader can be used in more than one vehicle. CAP
Bruno Turnout Turning Automotive Seating (Model Tas-2400/2400E)
The Bruno Turnout Turning Automotive Seating, model TAS-2400/2400E, is a swivel base designed for use by individuals with mobility disabilities who have difficulty getting in and out of a car or minivan. The unit is installed on a vehicle-specific custom base plate assembly and is available in a manual (TAS-2400) or powered (TAS-2400E) model. The seat rotates out over the doorsill, bridging the gap for a safe transfer onto the seat. Once the user is on the seat, it rotates back into the vehicle.
Car-Go-Mate Scooter Lift (Models Flc-0800-S & Flc-0800-Sb)
The Car-Go-Mate Scooter Lift is a hitch mounted scooter lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This exterior scooter lift installs on vehicles with a Class I or Class II 1.25-inch hitch receiver, and can handle scooters with a maximum width of 24.5 inches and a maximum wheelbase of 32 inches. The lift automatically clamps the scooter to the lift platform. It has a lifting range of 28 inches and a locking arm adjustment range of 3
Car-Go-Mate Wheelchair Lift
The Car-Go-Mate Wheelchair Lift is a hitch-mounted wheelchair carrier designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This exterior wheelchair lift installs on vehicles with a Class I or Class II 1.25-inch hitch receiver to hold manual wheelchairs. The wheelchair is automatically clamped to the lift platform, which folds and unfolds with the assistance of a gas-spring counterbalance. The lift is set low to reduce rear vision obstruction. The l
Cari All
Cari All is a hitch-mounted wheelchair or scooter carrier designed for use by individuals with mobility disabilities. Platform lift mounts to a Class III hitch for transporting powered scooters and non-folding wheelchairs. The lift is unfolded, raised, and lowered with a toggle switch, and folds up automatically when unloaded. Other features include auto-retractable ratchet straps for tie-down; an Integrated Suspension System (ISS) cushions the scooter or powerchair over bumps; a fully boxed bas
Carony Transportation System
Carony is a transport wheelchair base designed for use by individuals with severe physical disabilities or mobility disabilities who have difficulty entering and exiting minivans, pickup trucks, and full-size vans. The system operates in conjunction with a Bruno Turny or Turnout powered seat base. The user glides along a rail from the vehicle seat onto the wheeled base, remaining seated the whole time. A hand control glides the seat out of the vehicle then lowers the seat. The Turny or Turnout p
Chair Topper
The Chair Topper is a car top mounted wheelchair carrier designed for use by individuals with lower extremity and mobility disabilities, spinal cord injury and others who use a manual wheelchairs. Designed as an overhead wheelchair carrier for compact cars or sedans, this carrier is made of steel, aluminum and fiberglass. It folds, lifts and stores a folding manual wheelchair using power from a vehicle's 12 volt battery. Two switches control the 30-second cycle for stowing and extracting the whe
Chariot (Model: ASL-700)
Chariot (Model: ASL-700) is an exterior-style scooter and powerchair lift and trailer designed for people with severe physical disabilities, mobility disabilities, spinal cord injury and other mobility impairments that require the use of a scooter. The device mounts to the tow-hitch of a vehicle and can be transferred to any vehicle with a hitch. It leaves a user’s cargo space available. The Chariot's independent suspension carries the load's weight and 360-degree spinning wheels make it simple
Covered Outside Lift (Model Al3000)
The Covered Outside Lift, model AL3000, is a hitch-mounted scooter or powered wheelchair carrier designed for use by individuals who use wheelchairs. The plastic watertight cover keeps power chairs and scooters safe while the spring-assisted operation makes the cover easier to open and close. The carrier can be mounted on a class II or III trailer hitch and includes an integrated license plate mount. OPTIONS: Swing-away option. CAPACITY: 350 pounds. WARRANTY: Three-year transferable warranty.
Cradle To Hold Bike In The Back Of A Pickup.
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Cradle is designed to hold the front tires of two bicycles in a pickup truck but it could also be built to hold the two tires of a wheelchair. Wooden rack made from plywood and dowels. Twin cradles are mounted on a flat piece of plywood that lies on the truck bed. the base can be notched to fit any ribs in the truck bed. Includes photograph and drawing. SKILLS REQUIRED: Woodworking. TITLE: Cradle holds bike in back of a pickup. REF: Article: Sunset Mag
CTC 41
The CTC 41 (Cradle to Cradle) is a wheelchair prototype. This manual wheelchair features a honeycomb pattern that is extremely strong yet lightweight. The CTC 41 folds up like other collapsible chairs. The prototype includes personalization in wheel colors, frame colors, and even a special edition clear wheelchair.
Curb-Sider (Model Vsl-6000)
The Curb-Sider, model VSL-6000, is a trunk-mounted wheelchair alternative loader for persons with physical disabilities needing to transport power wheelchairs or scooters. This fully-powered lift fits most types of vehicle, including minivans, SUVs, CUVs, pickup trucks, and full-size vans. It is available for either the passenger or driver side, and its offset arm can pick up wheelchairs or scooters from the rear of the vehicle, from the rear corner, or from the side of the vehicle (near the rea
Curb-Sider (Model: VSL-6000/VSL-6900)
Curb-Sider (Model: VSL-6000/VSL-6900) is a hoist-style scooter and powerchair lift designed for people with severe physical disabilities, mobility disabilities, spinal cord injury and other mobility impairments that require the use of a scooter. The Curb-Sider's design lets users keep third-row seating when a mobility device isn't present in most vehicles. To use the device a user stands by the bumper, connects a docking device, pushes a button and the Curb-Sider lifts and stows the mobility dev
Cycle Rack
CUSTOM ADAPTATION PURPOSE: To enable an individual who uses a hand-propelled cycle wheelchair to transport it to cycling trails. A solution was developed that enables the individual to load the cycle, one end at a time, from his wheelchair onto a rack attached to a hitch on the back of his car. A short tubular bracket was attached transversely to the frame of the cycle at the center of gravity. A carrier pin was mounted to project horizontally from the hitch bracket; the pin engages with the tu
Diagonal Lifts
The Diagonal Lifts is designed for use by individuals with mobility disabilities or spinal cord injury. The lift encompasses both incline lifts for almost all types of stairs and vertical lifts for overcoming a variety of heights. It does not matter whether the installation is to be carried out inside buildings or out.
Electric Carrier & Carrier Cover Package (Models Wc210M-52 & Wc211M-52)
The Electric Carrier, model WC210M-52, is a Class 3 hitch mounted carrier for scooters or power wheelchairs. The lift is equipped with an electrical-operated screw jack that is activated by a switch. The power unit comes with a single wire that can be attached directly to the vehicle's electrical system or wired to a trailer plug. The power unit has built-in night lights which are switched on and off with a hidden push button under the red access cap. An emergency crank is also supplied to lower
Electric Cart Carrier
The Electric Cart Carrier is a hitch-mounted scooter carrier. This unit attaches to any vehicle with a class III hitch receiver and carries up to 500 pounds. It contains no wheels, axles, or hydraulics, which eliminates the need for special permits or licenses. The box-style unit has a lightweight extruded aluminum framework and a waterproof plywood floor. The unit has two retractable, stabilizing legs for use during loading and unloading and a ramp which doubles as a safety gate. It is equipped
Elite G2
The Elite G2 is a scooter or wheelchair loader for a van designed for use by individuals with mobility disabilities. This loader features a keychain remote control, a drive on/drive off platform, and quick cycling efficiency. DIMENSIONS: The platform is 44 x 27.5 inches. Stowed, the lift is 50 x 44 x 29.5 inches. CAPACITY: 350 pounds. WEIGHT: 200 pounds. COLOR: Available in five colors.
Equalizer Van Lift (Models Flc-0300-M25, Flc-0300-M40, Flc-0300-P25, Flc-0300-P40, Flc-0300-E25, & Flc-0300-E40)
The Equalizer Van Lift is a van or pickup truck wheelchair lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This powered lift adapts to most mini-vans, full sized vans, SUVs and pickup trucks, and fits other specialty vehicles such as the Chrysler PT Cruiser. It has a rotation range of 200 degrees. Equalizer 1 (FLC-0300-M25, FLC-0300-M40) is a power lift with manual rotation. Equalizer 2 (FLC-0300-P25, FLC-0300-P40) is a power lift with p
Excel & Excel Compact
The Excel & Excel Compact are wheelchair or scooter loaders vans designed for use by individuals with mobility disabilities. This boom lift features a wireless keychain remote control. DIMENSIONS: The vertical reach is 35.5 inches and the boom length is 38.25 inches on both models. The total height for the Excel is 39.25 inches and 31.75 inches for the Excel Compact. CAPACITY: 350 ponds on both models. WEIGHT: The installed weight for the Excel is 66 pounds and 64 ponds for the Excel Compact
Excel 200
The Excel 200 is a scooter or wheelchair loader designed for use by individuals with mobility disabilities. With five adjustments available to the dealer, this lift fits in most SUVs, minivans, station wagons, and the PT Cruiser and accommodates most scooters and lightweight powered wheelchairs. This lift offers both rear and curbside loading and the dual positioning base makes installationpossible on either the passenger or the driver's side of the rear cargo area. The Excel 200 lifts the po
Excel E & Excel E Compact
The Excel E & Excel E Compact are wheelchair or scooter loaders vans designed for use by individuals with mobility disabilities. This manual swing boom lift features push-button controls and adjustable locking "stops." DIMENSIONS: The vertical reach is 35.5 inches and the boom length is 38.25 inches on both models. The total height for the Excel is 39.25 inches and 31.75 inches for the Excel Compact. CAPACITY: 350 ponds on both models. WEIGHT: The installed weight for the Excel is 54 pounds
Gentleman's Pick-Up
--- "DO IT YOURSELF" ENTRY ------- PURPOSE: Pickup truck with wheelchair lift serves as less expensive alternative to a van. The user must, however, have residual ambulation ability. Describes use of a small pickup truck outfitted with a lift for an electric wheelchair. Presents advantages (i.e. cost and improved visibility) and disadvantages (possibility of rain damage, the need to be able to walk from the back of the truck to the cab), and makes suggestions concerning installation. Includes ph
Hercules (Models 2000 & 3000)
Hercules, model 2000 and 3000 is a trunk mounted scooter loader or van lift designed to lift scooters into vans or car trunks. These lifts feature an aluminized bronze sprocket that is non-corrosive and stronger than most steel. The sprocket assembly creates a four-to-one gear ratio for increased lifting capacity and the assembly is supported by a haf-inch steel shaft and needle bearing. The gearbox location allows greater height clearance and a low center of gravity provides ease in handling. T
Kar Kady
Wheelchair carrier attaches to standard trailer hitch (not included). Spring assist raises chair into storage position. Weight 13 pounds. Dimensions: 32.5 by 18 by 7.5 inches. Aluminum and stainless steel construction. Chair cover available ($65.95).
KMX Kompact R Trike
The KMX Kompact R Trike is ideal for wheelchair users under under 5 feet tall of varying abilities as it features a low center of gravity and very high stability. The sliding boom to make easy height adjustments so it can grow with the user. Features include:
Lectra Liftami
Electric lift for wheelchair alternatives. Bolts onto class 3 trailer hitch. Weight 62 pounds. Platform base folds up against rear of vehicle when not in use. Drive-on platforms available for 3 or 4 wheel scooters. Liftami II folds down to allow access to trunk or van doors. Includes night lift lights, high center-mounted brake light. Also available: nylon cover ($38.50); Inside trunk lift ($795.00).
Liberator Plus Trunk Lift (Model Flc-2000-Hdab)
The Liberator Plus Trunk Lift, model FLC-2000-HDAB, is a trunk mounted scooter or power wheelchair loader designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This heavy duty lift is constructed of welded steel with a powder coated finish, and comes with an adjustable reinforced deck base that bolts to the trunk or cargo area floor in a car, van, or SUV. It has a motorized lifting strap with a manual boom swing and hand held push button controls, a
Liberator Trunk Lift (Models Flc-0200-Ef & Flc-0200-Es)
The Liberator Trunk Lift is a trunk mounted scooter or power wheelchair loader designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Model FLC-0200-ES is stowable and model FLC-0200-EF is foldable. The lift is constructed of welded steel with a powder-coated finish, and comes with a deck base that bolts to the trunk or cargo area floor in a car, van, or SUV. It has a motorized lifting strap with a manual boom swing and hand held push button controls
Liberator With Hitch Mount Receiver Base (Models Flc-0200-Sr-2 & Flc-0200-Sr-3)
The Liberator With Hitch Mount Receiver Base is a hitch mounted scooter or power wheelchair loader designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. Model FLC-0200-SR-2 mounts to a Class II (1.25-inch) hitch receiver and model FLC-0200-SR-3 mounts to a Class III (2-inch) hitch receiver on a car, van, or SUV. Both are stowable. The lift is constructed of welded steel with a powder-coated finish, and comes with a motorized lifting strap, a manual
Lift'n'go (Model 210)
The Lift'N'Go, model 210, is a hitch-mounted wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. This electrically-powered universal carrier can be used to transport scooters and wheelchairs, including heavy scooters and mid-wheel drive chairs. It has a carrying platform with five tie-down locations and three nylon straps to secure the chair or scooter during transport. There is a backup hand crank with a stroke lift of 22 inches. The carrier requ
Lift-All
The Lift-All is an electric, trunk-mounted wheelchair loader with a built-in control. The lift is designed to be permanently installed in one side of a car's trunk or in a van, RV or truck. The lift's arm folds flat in the trunk, unfolds and locks in the operating position. The lift's boom swivels more than 90 degrees. The unit lifts the base of an Amigo with the seat and T-handle removed, but must be manually positioned over the trunk before lowering the scooter into the car's trunk. The lift c
Liftami Iii
Lift arm loads scooters into automobile trunks, vans, station wagons and hatchbacks. Vehicle installation involves bolting heavy duty base plate inside vehicle, and adjusting boom length and height to individual needs. The unit can be wired directly to auto battery or to scooter battery. Lifting is accomplished by an electric 12 volt screw actuator. Optional "C-Bar" lift arm allows scooters to be loaded without disassembly into mini vans, sport trucks or pickups. By removing seat and tiller, sco
Liftami Iv
Platform lift for electric wheelchairs up to 225 pounds. Also accommodates four wheel scooters. This unit bolts onto a class III receiver hitch and can be mounted to the rear of automobile by a local trailer hitch installer. A twelve volt motor raises and lowers the platform which can be folded and locked in vertical position when not in use. The platform is all aluminum and features "liftlites" for night use and a D.O.T. approved center breaklight.
Lifter (Model: AWL-150)
The Lifter (Model: AWL-150), is a trunk mounted wheelchair loader designed to lift and store manual folding wheelchairs into most models of automobiles, station wagons, hatchbacks, SUVs, or pick-up trucks that have sufficient room to store the chair. The lifter is made of steel tubing, and has a T-bar docking device that attaches to the mobility aid. The T-Bar detaches and the lift arm folds for storage. The unit lifts the chair up when the switch is activated and gently guides the lift arm and
Load 'n Go Power Wheelchair / Scooter Lift
The Load 'N Go Power Wheelchair/Scooter Lift is a truk mounted scooter or power wheelchair loader designed for use by individuals with mobility disabilities. This loader is designed for use in vehicles with hatchbacks. All lift functions are controlled by the touch of a button on a handheld pendant. The lift allows extended clearance between the vehicle and the scooter or wheelchair. A power swivel option guides the scooter or wheelchair into the vehicle.
Micro Inside Lift (Model Al055)
The Micro Inside Lift, model AL055, is a van lift without platform designed for use by individuals with mobility disabilities or spinal cord injury. This powered lift uses a boom with manual rotation to lift the lightweight wheelchair or travel scooter and can be used with vans, SUVs or the trunk of most cars. Docking devices are available to accommodate smaller scooters and chairs. The boom has a range of 360 degrees. DIMENSIONS: The lift requires 37 inches of headroom, but may be modified for
Micro Scooter Lift (Model Al010)
The Micro Scooter Lift, model AL010, is a hitch-mounted scooter carrier designed for use by individuals with mobility disabilities or spinal cord injury. This carrier is designed for lightweight micro or travel type three-wheel scooters. This compact carrier with a motorized lift can be mounted on a Class I, II, or III trailer hitch. The carrier folds manuallly and has a "hold down foot" feature for securing the scooter. POWER: Uses a battery and a supplied electrical harness with full-length le
Mobile-Lift Inside
The Mobile-Lift Inside, model 19680, is a wheelchair alternative lift for vans. The unit is installed inside a van, trunk, or station wagon and swings out and lowers the scooter. A claw hook and t-bar docking device allows fast loading with safe weight-balanced operation. The entire unit swivels on a roller-bearing surface. It comes with a quick disconnect plug set, as well as mounting hardware and installation instructions. Full-size scooters do not need to be disassembled for loading into
Mobile-Lift Outside
The Mobile-Lift Outside model is a bumper-mounted wheelchair alternative carrier designed to allow scooter users to drive onto the platform, get off, and push a switch to lift. The lift raises and locks any scooter into place on the back of a car in about 60 seconds. The unit folds up out of the way when not in use. A quiet, electric motor lowers the platform. The scooter is attached with adjustable safety belts. Two models are available. Model 19500 is designed for 3-wheel scooters and is t
Mobile-Lift Rv
The Mobile-Lift RV model is a hitch-mounted powered wheelchair alternative carrier designed for use on recreational vehicles. The lift raises and locks any scooter into place at the rear of the vehicle. The scooter does not need to be disassembled for loading. This powered lifter has an aluminum platform, two night lights for evening use, and a Department of Transportation-approved center brake light. The rectangular platform that folds up vertically when not in use. The lift is installed us
Omnigo Wheelchair Lift
The Omnigo Wheelchair Lift is a car top mounted wheelchair carrier for manual wheelchairs. The device is designed for less than a minute operation. A hand-controlled switch lowers the lift arm; the folded wheelchair wheels onto the loading arm; a second flip of the switch makes the chair automatically ascend to the top of the car and a cover lowers over the chair. The carrier mounts to the car top like a standard roof rack and causes minimum wind resistance. The device is made of aluminum and st
Out-Rider Vehicle Lift (Model Pul-1100)
The Out-Rider Vehicle Lift, model PUL-1100, is a wheelchair loader for pickup trucks designed to lift and store fully assembled scooters and manual wheelchairs behind the driver's cab of a full-size, mid-size, or king cab pick-up truck. The wheelchair lift can be mounted on the truck just behind the cab on either the driver's side or the passenger's side. A "docking device" is attached to the wheelchair; different devices are used for standard wheelchairs and for wheelchair alternatives. For sta
Pac All Bumper Deck
Platform mounts to the rear bumper of a car. Heavy duty aluminum frame. Provides access to trunk while the carrier is mounted. 28 inches wide by 23 inches deep. Rear supports are 28 inches high. Holds up to 150 pounds. Can be used to transport luggage, bikes, etc.
Pac All Dual Carrier
Bumper mounted carrier for standard wheelchair or scooter powered wheelchair. Fits on standard front or rear bumpers without a hitch (hitch adapter available). Support tubes are inserted into sockets and loack in place. Wheelchair or scooter must be lifted manually to knee height. Heavy duty rust proof aluminum. Includes all hardware and installation instructions.
Pac All Wheelchair Carrier
Wheelchair carrier installs on front or rear bumper of most automobiles, vans or recreational vehicles (RVs). Brackets attach to bumper and are the only visible component when the carrier is not in use. Support tubes insert in sockets and lock in place; wheelchair is tilted back and then forward to rest the rear wheel on its bracket. Tie down (included) secure the chair. Heavy duty rust proof aluminum.
Pac-All Scooter Carrier
Bumper mounted scooter carrier. Aluminum. Nylon straps. 150 pound maximum weight capacity. Fits on standard bumpers without hitch. Hitch adapter available. Scooter must be manually lifted to knee height. Cover available.
Pant Hook
The Pant Hook is an adaptive aid for wheelchair users it keeps your pants out of the way while catheterizing from your wheelchair. The paddle simply slides between the chair bottom and seat cushion and the hook is oriented to hook the waistband of your pants or underwear when you pull it up to your garment.
Patriot Power Chair Lift (Models Flc-0500-2 & Flc-0500-3)
The Patriot Power Chair Lift is a hitch mounted wheelchair lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The lift mounts on a Class II (model FLC-0500-2) or Class III (model FLC-0500-3) receiver hitch, and carries power chairs with a maximum width of 27 inches and a maximum wheelbase of 35 inches. POWER: Uses 12-volt direct current motor powered by the vehicle. WEIGHT: 110 pounds. CAPACITY: 160 pounds (model FLC-0500-2) or 300 pounds (m
Pioneer Hybrid Platform Lift (Model Al600)
The Pioneer Hybrid Platform Lift, model AL600, is a platform van lift designed for use by individuals with mobility disabilities or spinal cord injury. This device can lift a power wheelchair or scooter into the back of most SUVs, vans, or minivans. Features include a four-point universal securement system, and remote hand controls. The lift can be installed using existing third-row seating mounts as well as in vans without a third row. POWER: Uses battery and supplied electrical harness with fu
Sedona Powerchair Lift
The Sedona Powerchair Lift is a hitch-mounted scooter or powered wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. This lift raises and lowers a scooter or powerchair and is controlled by a key and a toggle switch. The lift is loaded and unloaded by driving on and driving off. The platform has a fully-automatic hold-down system. It tilts automatically on steep inclines and has an integrated suspension system to protect the scooter or powerchair.
Side Door Hybrid Platform Lift (Model Al690)
The Side Door Hybrid Platform Lift, model AL690, is a wheelchair or scooter loader for a van designed for use by individuals with mobility disabilities. This lift delivers a powered wheelchair or shorter scooter next to the driver or passenger's door. This lift features one-button operation with a handheld remote and uses second-row seat hardware for installation. DIMENSIONS: This lift has a 33.5 inch vertical reach and requires 32 inches of headroom and a depth of 58.5 inches. The platform is 2
Space Saver Take-Apart Scooter Lift (Model Asl-325)
The Space-Saver Take-Apart Scooter Lift, model ASL-325, is a trunk mounted wheelchair alternative loader for persons with mobility disabilities using scooters. The lift raises and stores scooters in cars with limited trunk space. It is height and length adjustable to fit any trunk size, and can lift scooters weighing up to 200 pounds. The Space-Saver is easily assembled and disassembled in three simple steps, with the heaviest part weighing just 13.5 pounds.
Spirit Scooter Lift (Models Flc-0400-2 & Flc-0400-3)
The Spirt Scooter Lift is a hitch mounted scooter lift designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The lift mounts to a Class II (model FLC0400-2) or Class III (model FLC-0400-3) receiver hitch. It can be configured for three or four wheel scooters. The scooter is automatically clamped after being driven onto the platform without additional tie-downs. The platform is weight-sensitive and automatically folds up and out of the way when lift
Standard Folding Wheelchair Carrier (Model Wc002M-52)
The Standard Folding Wheelchair Carrier, model WC002M-52, is a hitch mounted steel wheelchair carrier designed to carry a manual, folding wheelchair on the back of a car. The device mounts to a standard class 1 trailer hitch on a car. An anti-sway bracket helps the carrier from pivoting on the hitch. The carrier is bolted on and screwed with a wingnut. The chair is then lifted into position, and a locking arm is slid down tight and secured with a strap (included). A standard padlock will fit thr
Stroller Hardy
The Stroller Hardy is a mobility aid designed for children that offers maximum maneuverability for the caregiver and total comfort for the child. The Hardy features an adjustable height position so that the user can be at eye level of his or her friends. The Hardy can be used as a table seat to avoid a number of transfers between Hardy and other chairs.
Tailgater Pick-Up Truck Lift (Models Flc-0300-T25 & Flc-0300-T40)
The Tailgater Pick-Up Truck Lift is a wheelchair or scooter loader for pick-up trucks designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This powered lift with motorized rotation and a powered boom extension enables a power chair or scooter to be lifted from the cargo area of a pick-up truck and positioned beyond the lowered tailgate or next to the truck. Adjustable limit switches automatically stop rotation to prevent lift contact with the vehic
The Baby Beach Bug
The Baby Bug Aluminum Beach Jogger is a multi-position reclining seat designed to accommodate infants and children up to 40 pounds who have mobility disabilities. The Baby Bug Aluminum Beach Jogger has a removable child tray with 2 cup holders and toy steering wheel.
The Mountain Trike
The Mountain Trike is an all-terrain manual wheelchair designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. The Mountain Trike has been designed using a blend of unique innovation control and drive system with high specification mountain bike technology. Features include:
Tilt'n'tote (Model 001)
The Tilt'N'Tote, model 001, is a hitch-mounted wheelchair carrier designed to carry manual, folding wheelchairs on the bumper of cars. This device is made of steel and attaches to a standard Class 2 or 3 trailer hitch. It fits wheelchairs measuring up to 15 inches when folded. The carrier has an anti-sway bracket which can be installed or removed from a standard trailer hitch easily. To use, the release bar is pulled to permit the rack to tilt to the ground. The wheelchair is wheeled onto the Ti
Tilt'n'tote Plus (Model 004L)
The Tilt'N'Tote Plus, model 004L, is a hitch-mounted wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. It can be used to transport most pediatric and folding electric power chairs, including chairs up to 15.5 inches wide. The front saddle is adjustable to accommodate most lengths. The lift can be mounted on a Class 1, 2, or 3 hitch. CAPACITY: 100 pounds.
Tiny Tote 100 Manual Wheelchair Carrier
The Tiny Tote 100 Manual Wheelchair Carrier is a hitch-mounted wheelchair carrier desiged for use by individuals with mobility disabilities. This unit is used for transporting folding manual wheelchairs. The folded chair is placed on the platform, then the platform is tilted into place and the adjustable hold down arm secures the wheelchair. One handle is used to release the lift for both loading and unloading. The lift itself folds down so the user can access the vehicle's tailgate or lift gate
Tote Economy Carrier (Model 003)
The Tote Economy Carrier, model 003, is a hitch-mounted wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. This non-folding carrier can be used to mount any standard folding wheelchair using a Class 1, 2, or 3 hitch. CAPACITY: 75 pounds.
Tracker Inside Lift
The Tracker Inside Lift is a scooter and wheelchair loader designed for use by individuals with lower extremity or mobility disabilities or spinal cord injury. This lift has a drive-on lifting platform for power chairs and scooters, with two docking system options, the Dock 'N' Lock positive self-guiding manual release docking system and a strapping system. Once the power chair or scooter has been secured to the lifting platform, it is lifted and stowed inside the vehicle's cargo area. This lift
Uni-Lite
The Uni-Lite is a wheelchair lift for vans designed to ensure smooth, safe entry and exit for wheelchair users. With its compact design and large, non-skid, .25-inch thick aluminum platform, this lightweight conversion loader is adjustable to fit most van doors and is intended to maximize passenger space. Operated by a high-torque electric motor and direct gear drive, it features twin handrails with a control switch, a high-strength, aluminum alloy construction and a built-in manual backup syste
Universal Carrier (Model Wc010M-52)
The Universal Carrier, model WC010M-52, is a hitch mounted carrier for front or rear drive scooters or powered wheelchair alternatives, including batteries. The device mounts to a Class 3 (heavy duty), reinforced Class 2, Reese, or Draw-Tite frame hitch. The carrier platform is tipped down to load the mobility aid (scooters should be backed onto it), then tipped in the opposite direction and locked into place. Straps hold the mobility aid securely. The carrier is made of steel and steel grating
Universal Inside Lift (Model Al200)
The Universal Inside Lift, model AL200, is a wheelchair or scooter van loader designed for use by individuals with mobility disabilities or spinal cord injury. This is a heavy-duty lifter for heavier scooters and wheelchairs. It has an adjustable base that fits most vehicles on either side, and it disassembles into three components for stowage. It has a boom range of 360 degrees. POWER: Powered by the supplied electrical harness. The harness has full-length leads that attach directly to the bat
Universal Inside-Out Lift (Model Al065)
The Universal Inside-out Lift, model AL065, is a wheelchair or scooter van loader designed for use by individuals with mobility disabilities or spinal cord injury. This Class II or III hybrid mounts outside the vehicleand puts the scooter or chair inside, using a boom with a range of 100 degrees. The loader features weather resistant construction and a selection of docking devices for every scooter or chair. POWER: Uses battery and supplied electrical harness with full-length leads that attach
Universal Power Chair Lift (Model Al500)
The Universal Power Chair Lift, model AL500, is a hitch-mounted wheelchair carrier designed for use by individuals with mobility disabilities or spinal cord injury. This outside chair lift has an aluminum deck and automatic tensioners. It works on a Class II hitch-equipped vehicle with a hitch from 5 to 19 inches high, and supports power chairs with a maximum width of 28.5 inches. POWER: Uses battery and supplied electrical harness with full-length leads that attach directly to the battery. OPTI
Universal Scooter Lift (Model Al100)
The Universal Scooter Lift, model AL100, is a hitch-mounted scooter carrier designed for use by individuals with mobility disaabilities. This outside scooter lift works with any Class II hitch-equipped vehicle with a hitch from 5 to 19 inches high, and can support a scooter with a maximum width of 28.5 inches and a maximum wheelbase of 42 inches measured from the hub (center) of the front tire to the hub of the rear tire. The deck automatically folds up, out of the way, when empty. OPTIONS: A Sw
Walker Carrier
---- CUSTOMIZED ADAPTATION --------- PURPOSE: To create a custom adapted walker carrier frame for an individual with mobility disabilities due to lymphoedema. The individual could not transport her walker in the trunk or back seat of the family car, even when folded. While there were some commercially available carrier frames none fit the walker frame or could be used independently by the individual. A custom adapted carrier, which would fit into the car’s existing towbar socket, and meet the NS
WL-16RIII Walkbot
WL-16RIII Walkbot is a prototype of a bipedal robot (legs robot), designed for people with mobility impairments or walking disabilities. Like any other wheelchair, it rolls along on its wheels but, if a step or ditch gets in the way, the wheels transform into legs to carry the user over. It's intended facilitate movements in areas with steps and uneven surfaces are off-limits to those in wheelchairs.
Woolfe Scooter Lift
The Wolfe Scooter Lift is a scooter loader for vans designed for use by individuals who use wheelchairs. This lift can be installed in most full-sized mini-vans by General Motors or mini-vans by other manufacturers that have a hatch opening of 38 inches or greater. No vehicle modifications are required as this lift is designed to connect directly to the third-row seating floor mounts. A press of a button activates the lift and it automatically emerges from the back of the vehicle and lowers to t